
Peel strength decides whether a consumer opens a tray cleanly or reaches for a paring knife, and it also decides whether a seal survives high-pressure processing at 600 MPa. Easy-peel and lock-seal barrier films sit at opposite ends of that scale, with roughly a four-fold difference in force at the seal interface.
What Separates an Easy-Peel Film From a Lock-Seal Film
Both film types form a hermetic seal. The difference lives entirely in how that seal is designed to fail when a consumer pulls the corner tab.
How Easy-Peel Films Release
Easy-peel sealant layers are blended so the bond breaks at a predictable, repeatable force rather than holding until the film tears. Three mechanisms dominate commercial structures.
- Cohesive peel: the sealant layer splits internally, leaving a thin residue of polymer on the tray flange. Forgiving of temperature swings, which makes it common on high-speed lines.
- Adhesive peel: the bond releases at the interface between film and tray with no residue, producing the cleanest flange appearance.
- Delamination peel: an engineered layer inside the film structure separates, used where the sealant must also carry a reclose feature.
Typical target values run 2 to 5 N per 15 mm of seal width, measured per ASTM F88. Below about 1.5 N, the package becomes vulnerable in distribution; above 6 N, most consumers describe the package as difficult.
How Lock-Seal Films Fuse
Lock-seal structures, often called destructive or weld seals, use a sealant chemistry matched so closely to the tray resin that the two become a single mass at the flange. Seal strength commonly exceeds 15 N per 15 mm, and the film substrate tears before the seal opens. Opening requires a tear notch, a laser score, or a tool.
The Trade-Off Matrix: Integrity Against Ergonomics
Selection comes down to which failure the operation can least afford. A leaking tray of marinated protein in a distribution center costs more than a consumer complaint, but an elderly shopper who cannot open a single-serve meal stops repurchasing it.
- High-pressure processing: HPP at 87,000 psi flexes the entire package. Lock-seal or high-strength peel structures above 8 N per 15 mm are standard, since standard peel seals can pop at the flange corners.
- Heavy liquids and sauces: brines, broths and marinades load the seal hydraulically during transit. Lock-seal, or easy-peel with a wider 6 mm seal band.
- Ready meals and single-serve items: easy-peel at 2.5 to 4 N per 15 mm, often with a MAP gas flush holding residual oxygen under 1 percent.
- Retort and hot-fill: sealant layers must hold through 121 degrees Celsius processing, which pushes most structures toward lock-seal or specialty retort peel films.
- Dry snacks and produce: peel strength can sit at the lower end, since internal pressure is minimal.
Distribution channel shifts the calculation again. A tray that ships direct to consumer in a corrugated carton sees drop, vibration, and altitude changes that retail DC shipments do not, and many brands step peel strength up by 1 to 2 N when they move a SKU to e-commerce.
Matching the Sealant Layer to the Tray Resin
Substrate mismatch is the most expensive error in film selection because it looks like a packaging and sealing machine tray sealer problem for weeks before anyone questions the film. Polyolefins only bond reliably to like chemistries.
- PE trays: require a PE-based sealant. A PE peel film run on a PP tray typically produces almost no adhesion, since the two resins have different melt behavior.
- PP trays: need PP-compatible peel layers, often blended with PE to create the cohesive split. Seal temperatures usually run 10 to 20 degrees Celsius higher than PE equivalents.
- CPET and APET trays: paired with PET-based sealants or coated peel layers, generally sealing between 180 and 200 degrees Celsius.
- Fiber and coated paperboard trays: the coating forms the seal, not the fiber, so the film sealant must match the dispersion or PE barrier coating rather than the substrate.
Multi-substrate films exist and perform acceptably across PE, PP, and PET, but peel values vary across the range, sometimes by a factor of two. Operations running a single-tray resin usually get tighter seal distribution from a dedicated structure.
Three Failure Modes Worth Designing Out
Most field complaints trace back to one of three patterns, and each has a different root cause.
- Frustration failures: the film shreds, the tab delaminates, or the lid refuses to start. Usually caused by the seal temperature being set 10 to 15 degrees above the film’s window, which converts a peel seal into a partial weld.
- Channel leaks: product residue, fat or a deformed flange creates a microscopic path through the seal. Easy-peel films are less tolerant of contamination than weld seals because the bond strength is deliberately low.
- Substrate mismatch: either a blown seal in distribution or a lid that cannot be peeled at all. Verify the tray resin with the supplier rather than assuming, since converters sometimes change tray formulation without notice.
Flange cleanliness is the single highest-return fix on most lines. Adding a product deflector, trimming fill volume by 3 to 5 percent, or installing a flange wipe station routinely cuts leak rates more than any film change.
Validating a Film Before It Reaches Full Production
A designed trial takes less line time than three months of intermittent rejects. The sequence below covers the variables that interact.
- Step seal plate temperature in 5-degree increments across two or three dwell settings, typically 0.6 to 1.5 seconds for peel structures.
- Record seal strength at every point using a tensile test per ASTM F88, pulling at least five samples per condition.
- Run burst or dye penetration leak testing alongside strength data, since a strong seal and a hermetic seal are not the same result.
- Include deliberately contaminated flanges in the trial to find where the process window collapses.
- Confirm the sealant layer complies with food contact requirements through the supplier’s letter of guaranty, referencing FDA food contact substance regulations.
Consumer opening force deserves a seat in the protocol as well. Brands targeting older shoppers often validate against accessibility criteria similar to the Arthritis Foundation Ease of Use program, which evaluates whether packaging can be opened with limited grip strength.
Frequently Asked Questions
What Peel Strength Should an Easy-Peel Lidding Film Target?
Most food trays perform well between 2 and 5 N per 15 mm of seal width. Values under 1.5 N risk seal failure during stacking and transit, while anything over 6 N starts generating consumer complaints about difficult opening.
Can One Film Run on Both PP and CPET Trays?
Yes, multi-substrate peel films are formulated to bond across PP, PET, and PE, but peel values typically vary 1.5 to 3 times between substrates. Plants running a single-tray resin usually achieve tighter seal consistency with a dedicated sealant structure.
Does Easy-Peel Film Work With Modified Atmosphere Packaging?
Easy-peel films routinely hold residual oxygen below 1 percent in MAP applications. Barrier performance comes from the EVOH or PVDC layer inside the film structure, which is independent of the peel mechanism at the sealant surface.
Why Does the Lid Shred Instead of Peeling Cleanly?
Shredding almost always means the seal temperature or dwell exceeds the film’s peel window, turning a cohesive seal into a partial weld. Dropping plate temperature 5 to 10 degrees Celsius and re-testing seal strength resolves most cases within a single trial.
How Long Does a Film Qualification Trial Take?
A structured trial on an existing tray sealer typically takes four to eight hours of line time, plus two to three days for lab testing. Full commercial qualification, including shelf-life validation, generally runs four to eight weeks.
Send Your Trays and Film Specs to RTG for Seal Matching
RTG film specialists run sample matching and seal testing against the trays and equipment already on your floor, so the recommendation accounts for your actual flange geometry, product load, and cycle rate. Contact the team with your tray resin, product type, and target peel range to schedule a trial.